Clarification from the agency

1. Washington Army National Guard Permanent or Indefinite Employees. 2. Washington Army National Guard Traditional Guard members and Washington National Guard Active Guard Reserves.

A WG-2602-11, ELECTRONIC MEASUREMENT EQUIPMENT MECHANIC:

• Calibrates and repairs TMDE within support capability and authority including various levels of calibration as designated in technical bulletins, manuals, etc. Performs functional electronic, physical, and radioactive testing involving interpretation and analysis of measurement data, in accordance with cyclic inspection requirements. Aligns, troubleshoots, tests, inspects, repairs, modifies, calibrates and certifies precision measurement equipment such as multimeters, microwave equipment, oscilloscopes, temperature analyzers, mercurial barometers, gage blocks and micrometer caliper dimensional equipment, digital voltmeters, signal generators, torque wrenches, pressure gauges, torque testers, weight scales, electronic counters, radiation monitors, radix calibrators, and radiation dosimeters. Analyzes and isolates component malfunctions; calculates and determines tolerances; and performs tests and calibrations in accordance with instructions, which are often vague and incomplete, and may require the preparation of diagrams and instructions to facilitate the calibration action.
• Sets up system test sets and various types of test equipment such as frequency meters, standing wave ratio meters, radio frequency (RF) power meters, function/ arbitrary waveform generator, distortion analyzers, time frequency work stations, oscillators, voltmeters, electronic counters, oscilloscopes, attenuators, decade resistors and capacitors, signal generators, stroboscope, tachometers, pneumatic and hydraulic pressure standards and other physical and electronic tests.
• Following repair, tests by applying signals in known amplitude and wave shape into oscilloscopes to observe wave pattern. Isolates faults by taking measurements and comparisons in voltage, amperage, ohms, henries, power factor, watts, temperature, humidity, microns, foot-pounds, decibels, sensitivity, noise, stability, Voltage Standard Wave Ratio (VSWR), impedance, phase, absolute pressure, time intervals, displacement, flow rate, etc., to determine performance of equipment. If signal is distorted, traces it through electronic stages to locate malfunctioning part. Checks sweep rate by feeding known signal to an oscilloscope and observing wave pattern to correct shape and size. Operates equipment to complete range checking for proper operation of positioning controls. Adjusts with trimmer potentiometers; and if calibration is still not possible, adds or removes sufficient resistance to permit balancing of circuit. As needed, contacts the using organization to obtain information concerning the nature of the malfunction.
• Determines purpose in operation characteristics of each major section. Refers to technical manuals and manufactures specifications to obtain information on operation characteristics of circuit components such as integrated circuits, microprocessors, decoders, latching networks, notch filters, logics, controllers, programmable gain amplifiers, digital displays, transistors, tubes, transformers, coils, relays, motors, and similar devices. Disassembles, cleans and inspects parts such as printed circuit boards, resistors, capacitors, integrated circuits, relays, chambers, cables, and wiring for evidence or wear or malfunction. Repairs and/or replaces parts as required. Uses special test devices and radioactive samples or other calibrated sources. Tests equipment for sensitivity and correct operation. Observes necessary precautions as stipulated in operational repair manuals. Makes radiation calculations/readings at various distances from the standard ensuring radiation equipment is operating in specified parameters. Performs contamination/radiation surveys on radiation equipment to control/eliminate radiation leakage/contamination.
• Completes necessary Army Maintenance Management System (TAMMS), calibration, radiation reports and other records and forms on work completed. Ensures maximum number of weapons systems are operationally ready. Uses TMDE Integrated Maintenance Management Systems (TIMMS) for all supported equipment to track, turn-in, repair, calibrate, and return to the end user in a timely fashion to prevent work stoppages. Furnishes technical data to the supervisor for inclusion in reports as well as recommending equipment improvement and solutions for unusual problems related to testing and the use of precision TMDE.
• Follows appropriate safety procedures, with special care being exercised while calibrating high voltage, radio frequency, radioactive sources and high-pressure instruments and gages. Performs and interprets wipe tests on radiation sources for possibility of radiation hazards. Familiar with and abides by all Federal and State regulations concerning handling, transportation and disposal of radioactive waste or devices.
• Other duties as assigned.

Conditions of employment

MILITARY REQUIREMENTS:

Military Grades: E1 - E9, WO1

Desired Military Assignments: 94/25/91/92/12/88/915/948/922

- Applicants need not be assigned to the position or possess the MOS to apply or be considered for selection. Selected applicant must be assigned to a compatible Military position and attain MOS within 1 year of appointment action.

- May be required to successfully complete a trial period.

- Participation in direct deposit is mandatory.

- All soldiers, civilian employees, and contractor employees who drive Army-owned or leased vehicles must complete the Army Avoidance Course (AAC) training when they start working for the Army. Must have a valid Washington state and military driver's license. Must be able to obtain a Government Travel Card (GTC) and be able to attend all schools deemed necessary by the supervisor.

- Males born after 31 December 1959 must be registered for Selective Service.

- Must maintain membership in the WA Army National Guard for continued employment.

- Must be able to obtain and maintain the appropriate security clearance of the position.

- This position is covered by the Domestic Violence Misdemeanor Amendment (30 Sep 96) of the Gun Control Act (Lautenberg Amendment) of 1968. An individual convicted of a qualifying crime of domestic violence may not perform the duties of this position.

- Position requires ability to establish effective professional working relationships with coworkers and customers, contributing to a cooperative working environment and successful accomplishment of the mission.

- May occasionally be required to work other than normal duty hours; overtime may be required.

- The duties and responsibilities of your job may significantly impact the environment. You are responsible to maintain awareness of your environmental responsibilities as dictated by legal and regulatory requirements, your organization, and its changing mission.

Qualifications

GENERAL EXPERIENCE:
Experience or training which demonstrates a working knowledge of electronic principles involved in the generation and measurement of such elements as voltage, current, impedance, capacitance, frequency, and inductance. Experience in the use of various precision measurement instruments and standards.

SPECIALIZED EXPERIENCE:
Must have at least 18 months of experience or training with basic application of operating principles such as the production and utilization of oscillations over a broad range of frequencies; signal and waveform behavior, distortion, and amplification; pulse, trigger, and synchronization techniques; digital/analog processing and data conversion techniques; and a variety of display and indication methods. Experience in tracing signals and voltage paths, and skilled in the analysis of waveform characteristics such as timing, duration, frequency, and phasing. Originates test set-ups to isolate malfunctions and check performance characteristics of special or unique test panels or mockups. Experience in interpreting and applying a variety of technical electronic information such as schematic symbols, mathematical expressions and formulas, calibration procedures, and other reference materials. Experience in applying established techniques and methods of repair, testing, alignment, and calibration of equipment, which serves as test equipment or precision measurement standards. Experience in utilizing electronic circuits to measure electronic or electrical quantities to determine the performance characteristics and accuracy of other instruments and equipment.

How you will be evaluated

You will be evaluated for this job based on how well you meet the qualifications above.

Once the announcement has closed, your resume and supporting documentation will be used to determine if you meet the qualifications listed on this announcement. If you are minimally qualified, your resume and supporting documentation will be compared to your responses on the assessment questionnaire to determine your level of experience. If you rate yourself higher than is supported by your application package, your responses may be adjusted and/or you may be excluded from consideration for this position. You may also be excluded from consideration if you indicate that you are unwilling to accept the lower grade and a determination is made that you are not qualified at the higher grade. If you are found to be among the top qualified candidates, you will be referred to the selecting official for employment consideration.

Verbiage displayed on your resume or application must contain your own words. You may refer to position descriptions, i.e. the general and specialized experience located within the vacancy announcement, to assist with describing work experiences; however, resumes or applications received in verbatim will not be considered. In your resume you will need to address the general and specialized experience listed above. Please use as much detail as needed, giving dates (months and years) of the experience, position title and how the experience was gained. This information is needed to determine if you are qualified for the position.

Your qualifications will be evaluated on the following competencies (knowledge, skills, abilities, and other characteristics). NOTE: You do not have to respond to the KSA's separately but your resume should contain sufficient information to demonstrate possession of the KSA's.

• Practical application of operating principles such as the production and utilization of oscillations over a broad range of frequencies; signal and waveform behavior, distortion, and amplification; pulse, trigger, and synchronization techniques; digital/analog processing and data conversion techniques; and a variety of display and indication methods.
• Familiarity with the methods of signal modulation and electromagnetic radiation.
• Thorough knowledge of the methods and techniques of precise measurements of electrical and electronic quantities and relationships such as standing wave ratio, power, impedance, reactance, and attenuation.
• Ability to trace signals and voltage paths, and skilled in the analysis of waveform characteristics such as timing, duration, frequency, and phasing. Originates test set-ups to isolate malfunctions and check performance characteristics of special or unique test panels or mockups.
• Familiarity with the functional relationships of circuits, assemblies, and equipment serviced.
• Ability to judge the impact of repairs on related integral devices, and perform further adjustments and alignments.
• Familiarity with the operation, capabilities, and limitations of such precision measurement instruments as spectrum and distortion analyzers, digital and differential meters, multi-channel oscilloscopes, waveguide equipment, oscillators, and a variety of precision frequency and time measurement standards.
• Ability to install major modifications to instruments and equipment in accordance with instruction and procedures.

To apply for this position, you are required to submit a complete application package. If you fail to provide this documents/information, you will be marked as having an incomplete application package and will not be considered any further. Resumes must be in your own words. Resumes that are verbatim, from this announcement, will not be considered.

1. Resume must NOT exceed two (2) pages, IAW Merit Hiring Plan and must include:
   • Contact information
     • Full Name
     • Email Address
     • Phone Number
   • Relevant work history that demonstrates specialized experience for the position you are applying to
     • Position Title
     • Organization/Department/Unit
     • Hours worked per week
     • Dates (format should include Month and Year) of employment
     • Duties performed
     • Series and grade for federal positions, if held
   • Resumes exceeding 2 pages will not be considered. For more guidance please see new resume guidance.
   • If your resume includes the below listed content, it will not be used to make an eligibility/qualification determination, and you will not be considered for this vacancy.
     • Classified or government sensitive information
     • Social Security Number (SSN)
     • Photos of yourself
     • Personal information, such as age, gender, religious affiliation, etc.
2. Mil Form 174 Mil Form 174 is required. Applications without the Mil Form 174 will not be considered
   • If you do not have prior military service, please indicate so on the form. (This position requires Military membership in the Washington State Army National Guard).
3. Other support documentation (optional or required based on the vacancy announcement)
   • Cover Letter
   • DD-214
   • SF-50 (latest non-award SF-50)
   • Transcript (s)

***For current Guard/Reserve members, please document your military work experience as follows: (You may adjust the format, so that you do not exceed the two (2) page resume limit, as long as your resume clearly reflects your military employment history.)

List month joined (to/from) based on your enlistment contract (DD4) or (Oath) for Officers. If you have gaps in service, list them separately.

Example:

04 Sep 2019 to 03 Sep 2023
Washington Air National Guard
Traditional Member
20 hours per month
POSITIONS TITLE MOS/AFSC
Personnel Superintendent 3S091
Duties

Military Orders During this period: (list multiple periods if everything else is the same: Order Type, Duties, & Purpose)

04 Nov 2019 to 03 Dec 2019, 40 hours per week
15 Mar 2020 to 14 May 2020, 40 hours per week
Type of Order: ADOS/AT/ST/AGR
Order Purpose:
Duties:

***If there are multiple purposes on a single order (ie. BMT then Tech Training/AIT), list specific periods. Example: Order cover 02 Sep 2020 to 12 Mar 2021:

List 02 Sep 2020 to 01 Nov 2020 as BMT and 02 Nov 2020 to 12 Mar 2021 as Tech Training/AIT


For access to Required Documents please refer to: http://mil.wa.gov/federal-human-resources

Next steps