Duties
Major Duties: This is not an all-inclusive list
A ELECTRONIC MEASUREMENT EQUIPMENT MECHANIC (T32), WG-2602-11,
(1) Calibrates and repairs TMDE within support capability and authority including various levels of calibration as designated in technical bulletins, manuals, etc. Performs functional electronic, physical, and radioactive testing involving interpretation and analysis of measurement data, in accordance with cyclic inspection requirements. Aligns, troubleshoots, tests, inspects, repairs, modifies, calibrates and certifies precision measurement equipment such as multimeters, microwave equipment, oscilloscopes, temperature analyzers, mercurial barometers, gage blocks and micrometer caliper dimensional equipment, digital voltmeters, signal generators, torque wrenches, pressure gauges, torque testers, weight scales, electronic counters, radiation monitors, radix calibrators, and radiation dosimeters. Analyzes and isolates component malfunctions; calculates and determines tolerances; and performs tests and calibrations in accordance with instructions, which are often vague and incomplete, and may require the preparation of diagrams and instructions to facilitate the calibration action.
(2) Sets up system test sets and various types of test equipment such as frequency meters, standing wave ratio meters, radio frequency (RF) power meters, function/ arbitrary waveform generator, distortion analyzers, time frequency work stations, oscillators, voltmeters, electronic counters, oscilloscopes, attenuators, decade resistors and capacitors, signal generators, stroboscope, tachometers, pneumatic and hydraulic pressure standards and other physical and electronic tests. Diagnoses equipment, makes repairs, and replaces defective parts/components such as integrated circuits, printed circuit boards, electronic condition coils, radiation detector boards/circuits, crystals, transistors, tubes, transformers, condensers, diodes, relays potentiometers, and related components.
(3) Following repair, tests by applying signals in known amplitude and wave shape into oscilloscopes to observe wave pattern. Isolates faults by taking measurements and comparisons in voltage, amperage, ohms, henries, power factor, watts, temperature, humidity, microns, foot-pounds, decibels, sensitivity, noise, stability, Voltage Standard Wave Ratio (VSWR), impedance, phase, absolute pressure, time intervals, displacement, flow rate, etc., to determine performance of equipment. If signal is distorted, traces it through electronic stages to locate malfunctioning part. Checks sweep rate by feeding known signal to an oscilloscope and observing wave pattern to correct shape and size. Operates equipment to complete range checking for proper operation of positioning controls. Adjusts with trimmer potentiometers; and if calibration is still not possible, adds or removes sufficient resistance to permit balancing of circuit. As needed, contacts the using organization to obtain information concerning the nature of the malfunction.
(4) Determines purpose in operation characteristics of each major section. Refers to technical manuals and manufactures specifications to obtain information on operation characteristics of circuit components such as integrated circuits, microprocessors, decoders, latching networks, notch filters, logics, controllers, programmable gain amplifiers, digital displays, transistors, tubes, transformers, coils, relays, motors, and similar devices. Disassembles, cleans and inspects parts such as printed circuit boards, resistors, capacitors, integrated circuits, relays, chambers, cables, and wiring for evidence or wear or malfunction. Repairs and/or replaces parts as required. Uses special test devices and radioactive samples or other calibrated sources. Tests equipment for sensitivity and correct operation. Observes necessary precautions as stipulated in operational repair manuals. Makes radiation calculations/readings at various distances from the standard ensuring radiation equipment is operating in specified parameters.
(5) Completes necessary Army Maintenance Management System (TAMMS), calibration, radiation reports and other records and forms on work completed. Ensures maximum number of weapons systems are operationally ready. Uses TMDE Integrated Maintenance Management Systems (TIMMS) for all supported equipment to track, turn-in, repair, calibrate, and return to the end user in a timely fashion to prevent work stoppages. Furnishes technical data to the supervisor for inclusion in reports as well as recommending equipment improvement and solutions for unusual problems related to testing and the use of precision TMDE.
(6) Follows appropriate safety procedures, with special care being exercised while calibrating high voltage, radio frequency, radioactive sources and high-pressure
Performs other duties as assigned.
The above does not list all duties. The full list of duties can be provided upon request.
Requirements
Conditions of employment
CONDITIONS OF EMPLOYMENT
- Minnesota National Guard Membership is required. If you are not sure you are eligible for military membership, please contact a National Guard recruiter prior to applying for this position. Applicants who are not currently a member of the MN National Guard must be eligible for immediate membership and employment in the National Guard in the military grade listed in this announcement.
- Selectee will be required to wear the military uniform.
- Federal employment suitability as determined by a background investigation.
- May be required to successfully complete a probationary period.
- Acceptance of an excepted service position constitutes concurrence with these requirements as a condition of employment.
- Must be able to obtain and maintain the appropriate security clearance of the position.
- Most MNNG position are covered by the Domestic Violence Misdemeanor Amendment (30 Sep 96) of the Gun Control Act (Lautenberg Amendment) of 1968. An individual convicted of a qualifying crime of domestic violence may not perform the duties of this position.
- Irregular and/or overtime (compensatory) hours may be required to support operational requirements or contingencies or may be required to work hours outside of the normal duty day.
MILITARY COMPATIBILITY:
Upon selection, individuals will undergo a background check to validate suitability for employment with the federal government as permitted by law, regulation, Presidential order or other authority. Suitability is dependent upon the particular requirements for security clearance, sensitivity level, and DOD IT network access. Items checked include, but are not limited to all criminal history record information, employment history, education and fiscal accountability/responsibility.
The individual selected must be assigned to a compatible military position and must also maintain satisfactory membership in the Minnesota Army National Guard.
Qualifications
In order to qualify, you must meet the experience requirements described below. Experience refers to paid and unpaid experience, including volunteer work done through National Service programs (e.g., Peace Corps, AmeriCorps) and other organizations (e.g., professional; philanthropic; religious; spiritual; community; student; social). You will receive credit for all qualifying experience, including volunteer experience. Your resume must clearly describe your relevant experience; if qualifying based on education, your transcripts will be required as part of your application. In describing your experience, please be clear and specific. We will not make assumptions regarding your experience. Do not copy and paste the duties, specialized experience, or occupational assessment questionnaire from this announcement into your resume as that will not be considered a demonstration of your qualifications for this position.
MILITARY GRADES: E1-E9, WO1-CW2
Failure to obtain a compatible MOS may result in termination of employment.
GENERAL AND SPECIALIZED EXPERIENCE QUALIFICATIONS REQUIREMENTS:
Description of Work:
Work involved in the maintenance, repairs, calibration, and certification of electronic test, measurement, and reference equipment used for precise measurement of a variety of electrical and electronic values. Quantities and relationships such as voltage, resistance, capacitance, frequency, and inductance.
Minimum Requirements:
WG- Experience or training which demonstrates a working knowledge of electronic principles involved in the generation and measurement of such elements as voltage, current, impedance, capacitance, frequency, and inductance. Experience in the use of various precision measurement instruments and standards.
Specialized Experience:
WG-09 and above - Experience or training with basic application of operating principles such as the production and utilization of oscillations over a broad range of frequencies; signal and waveform behavior, distortion, and amplification; pulse, trigger, and synchronization techniques; digital/analog processing and data conversion techniques; and a variety of display and indication methods. Experience in tracing signals and voltage paths, and skilled in the analysis of waveform characteristics such as timing, duration, frequency, and phasing. Originates test set-ups to isolate malfunctions and check performance characteristics of special or unique test panels or mockups. Experience in interpreting and applying a variety of technical electronic information such as schematic symbols, mathematical expressions and formulas, calibration procedures, and other reference materials. Experience in applying established techniques and methods of repair, testing, alignment, and calibration of equipment, which serves as test equipment or precision measurement standards. Experience in utilizing electronic circuits to measure electronic or electrical quantities to determine the performance characteristics and accuracy of other instruments and equipment.
Education
EDUCATION: NA
You must provide transcripts or other documentation to support your Educational claims. To receive credit for Education, you must provide documentation of proof that you meet the Education requirements for this position.
Additional information
REMARKS: No PCS available. Position will not be filled until current incumbent vacates. Sensitivity Level 2. Participation in direct deposit is mandatory. - Males born after 31 December 1959 must be registered for Selective Service.
Acceptance of a Technician position may result in the termination of your Selected Reserve bonus.
IMPORTANT NOTES:
- Should a position be announced at less than the authorized grade, the selected applicant may be non-competitively promoted when he/she meets all qualifications and is submitted for promotion by the supervisor.
- IAW NGR 600-25 AND AFI 36-101, grade inversion within the full-time workforce is not permitted.
- Males applicants born after 31 December 1959 must be registered with the Selective Service System in compliance with the Defense Authorization Act of 1986, Section 1622 (https://www.sss.gov/RegVer/wfRegistration.aspx).
This is an Excepted Service position that requires active membership in a compatible MOS in the Minnesota Army National Guard and wear of the military uniform. Acceptance of an Excepted Service position constitutes concurrence with these requirements as a condition of employment. Applicants who are not currently enlisted in the Minnesota Army National Guard must be eligible for immediate enlistment or appointment. For enlistment/appointment criteria, consult www.nationalguard.com. Military skill set is determined by MOS requirements. Upon selection, individuals must be assigned to a compatible military MOS in accordance with statutes and National Guard Bureau regulations and must obtain/maintain all requirements of the AFSC/MOS.
The Minnesota Department of Military Affairs is an Equal Opportunity Employer. All qualified applicants will receive consideration for the position without discrimination for any non-merit reason(s) such as age, race, religion, gender, ethnic origin or non-disqualifying disability. Pre-selection is not only counter-productive to effective recruitment and placement, but also violates The Merit Placement Principles and will not be tolerated.
If you have information or questions regarding this issue, please contact the Equal Employment Manager at 651-282-4472 or 651-282-4078.
Candidates should be committed to improving the efficiency of the Federal government, passionate about the ideals of our American republic, and committed to upholding the rule of law and the United States Constitution.
A career with the U.S. government provides employees with a comprehensive benefits package. As a federal employee, you and your family will have access to a range of benefits that are designed to make your federal career very rewarding. Opens in a new windowLearn more about federal benefits.
Review our benefits
Eligibility for benefits depends on the type of position you hold and whether your position is full-time, part-time or intermittent. Contact the hiring agency for more information on the specific benefits offered.
How you will be evaluated
You will be evaluated for this job based on how well you meet the qualifications above.
AREAS OF PRIORITY: In Accordance with MN National Guard Regulation 690-335 (Army) or 36-1 (Air), Applications will be forwarded to the selection official to conduct reviews by area of priority as listed below
Area 1: Current On-board Minnesota National Guard Title 32 Technicians who are in permanent or indefinite technician status as a result of being competitively hired within that National Guard component applying for a position within the component which they are currently employed.
Area 2: Current Minnesota National Guard Title 32 Technicians who are in permanent or indefinite technician status as a result of being competitively hired at a sister component that is identified on the Position Vacancy Announcement (PVA), including onboard Title 5 employees that are also current members of MNNG; i.e. Army MNNG to Air MNNG, Air MNNG to Army MNNG.
Area 3: All Minnesota National Guard members currently assigned to the MNANG or to the MNARNG applying for a position within the component in which they are currently assigned. i.e. temporary technician or Traditional Guardsman.
Area 4: Currently assigned service members in other branches of the military outside of the Minnesota National Guard, to include those assigned to Active Duty, Reserve or other state's National Guard.
Area 5: All individuals able to and willing to become members of the Minnesota National Guard including prior service not currently assigned to a military component and non-prior service US civilians.
Evaluation Factors: Candidates will be evaluated on the basis of appropriate education, experience, training, self-development activities, and special awards. Candidates are considered on the basis of available information on their current application and supporting information that has been provided to this office. To ensure full consideration, applicants are urged to submit information about their training, self-development, outside experience, activities and awards. National Guard military (Part-time) service is considered as full-time experience when evaluated against the qualification requirements for a technician position. The applicant is credited with actual number of months the member has been in the National Guard if the experience is related.
Once the announcement has closed, your resume and supporting documentation will be used to determine if you meet the qualifications listed on this announcement. If you are minimally qualified, your resume and supporting documentation will be compared to your responses on the assessment questionnaire to determine your level of experience. If you rate yourself higher than is supported by your application package, your responses may be adjusted and/or you may be excluded from consideration for this position. If you are found to be among the top qualified candidates, you will be referred to the selecting official for employment consideration.
Required Documents
To apply for this position, you MUST submit a complete Application Package which includes:
1. Resume showing work schedule (Full-time, Part-time, Intermittent), hours worked per week, To and From Dates (format must include Month and Year, e.g, 02/2017, Feb 2017, ect.) of employment and duties performed. In describing your experience, please be clear and specific. It is your responsibility to make sure your resume states complete information for each job entry (beginning and ending dates of employment stated as MM/DD/YYYY; and total hours worked per week). If your resume does not provide enough information regarding your work history for us to make a creditable qualification determination, your application package may be rendered disqualified, and you will no longer be considered for this position.
2. Transcript: If position requires a degree or if using education to qualify
3. The AGO 163 can be submitted to reflect your military experience.
4. The OF 612 is optional but will not be used in lieu of a resume.
Other Required Documents: Additional certifications, transcripts, training reports, and related credentials as applicable
Job Information: Vacancy Identification Number ( 13084522 ), title ( ELECTRONIC MEASUREMENT EQUIPMENT MECHANIC (T32) ) and Grade(s) ( 11 ) for which you are applying for.
Do not include the following types of information in your profile or resume:
- Classified or government sensitive information
- Social Security Number (SSN)
- Photos of yourself
- Personal information, such as age, gender, religious affiliation, etc.
- Encrypted and digitally signed documents
If you are relying on your education to meet qualification requirements:
Education must be accredited by an accrediting institution recognized by the U.S. Department of Education in order for it to be credited towards qualifications. Therefore, provide only the attendance and/or degrees from
schools accredited by accrediting institutions recognized by the U.S. Department of Education.
Failure to provide all of the required information as stated in this vacancy announcement may result in an ineligible rating or may affect the overall rating.