ELECTRONIC MEASUREMENT EQUIPMENT MECHANIC TITLE 32 TEMPORARY NTE 1 NOV 2027

Clarification from the agency

This is a deployment backfill Not To Exceed 1 Nov 2027.

The primary purpose of this position is to perform calibration, diagnostics repair, and certification of electronic, mechanical, and radiation Test Measurement and Diagnostic Equipment (TMDE).

Sets up system test sets and various types of test equipment such as frequency meters, standing wave ratio meters, radio frequency (RF) power meters, function/ arbitrary waveform generator, distortion analyzers, time frequency work stations, oscillators, voltmeters, electronic counters, oscilloscopes, attenuators, decade resistors and capacitors, signal generators, stroboscope, tachometers, pneumatic and hydraulic pressure standards and other physical and electronic tests. Diagnoses equipment, makes repairs, and replaces defective parts/components such as integrated circuits, printed circuit boards, electronic condition coils, radiation detector boards/circuits, crystals, transistors, tubes, transformers, condensers, diodes, relays potentiometers, and related components.

Following repair, tests by applying signals in known amplitude and wave shape into oscilloscopes to observe wave pattern. Isolates faults by taking measurements and comparisons in voltage, amperage, ohms, henries, power factor, watts, temperature, humidity, microns, foot-pounds, decibels, sensitivity, noise, stability, Voltage Standard Wave Ratio (VSWR), impedance, phase, absolute pressure, time intervals, displacement, flow rate, etc., to determine performance of equipment. If signal is distorted, traces it through electronic stages to locate malfunctioning part. Checks sweep rate by feeding known signal to an oscilloscope and observing wave pattern to correct shape and size. Operates equipment to complete range checking for proper operation of positioning controls. Adjusts with trimmer potentiometers; and if calibration is still not possible, adds or removes sufficient resistance to permit balancing of circuit. As needed, contacts the using organization to obtain information concerning the nature of the malfunction. Uses equipment schematics to analyze circuits by preparing block diagram showing major components such as amplifiers, filters, oscillators and indicators.

Determines purpose in operation characteristics of each major section. Refers to technical manuals and manufactures specifications to obtain information on operation characteristics of circuit components such as integrated circuits, microprocessors, decoders, latching networks, notch filters, logics, controllers, programmable gain amplifiers, digital displays, transistors, tubes, transformers, coils, relays, motors, and similar devices. Disassembles, cleans and inspects parts such as printed circuit boards, resistors, capacitors, integrated circuits, relays, chambers, cables, and wiring for evidence or wear or malfunction. Repairs and/or replaces parts as required. Uses special test devices and radioactive samples or other calibrated sources. Tests equipment for sensitivity and correct operation. Observes necessary precautions as stipulated in operational repair manuals. Makes radiation calculations/readings at various distances from the standard ensuring radiation equipment is operating in specified parameters. Performs contamination/radiation surveys on radiation equipment to control/eliminate radiation leakage/contamination.

Completes necessary Army Maintenance Management System (TAMMS), calibration, radiation reports and other records and forms on work completed. Ensures maximum number of weapons systems are operationally ready. Uses TMDE Integrated Maintenance Management Systems (TIMMS) for all supported equipment to track, turn-in, repair, calibrate, and return to the end user in a timely fashion to prevent work stoppages. Furnishes technical data to the supervisor for inclusion in reports as well as recommending equipment improvement and solutions for unusual problems related to testing and the use of precision TMDE.

Conditions of employment

• NATIONAL GUARD MEMBERSHIP IS REQUIRED. If you are not sure you are eligible for military membership, please contact a National Guard recruiter prior to applying for this position.
• This is an TEMPORARY excepted service position that requires membership in a compatible military assignment in the employing state's National Guard, required prior to the effective date of placement.
• Selectee will be required to wear the military uniform.
• Acceptance of an excepted service position constitutes concurrence with these requirements as a condition of employment.
• Males born after 31 December 1959 must be registered for Selective Service.
• Federal employment suitability as determined by a background investigation.
• May be required to successfully complete a probationary period.
• Participation in direct deposit is mandatory.
• Must have a military drivers license.

Qualifications

Compatible military grade and assignment required prior to the effective date of placement. This is a Title 32 TEMPORARY excepted service position that requires membership in a compatible military assignment in the employing state's National Guard.

Military Grades: Enlisted E2 to E8

Selectee(s) must be within the military grade(s) listed in this job announcement prior to the effective date of placement into the technician position.

Applicant(s) (Enlisted) who are over grade must clearly state, in their resumes, their intentions to willingly take a reduction in grade.

Compatible Military Assignments: 88. 91, 94

GENERAL EXPERIENCE: Experience or training which demonstrates a working knowledge of electronic principles involved in the generation and measurement of such elements as voltage, current, impedance, capacitance, frequency, and inductance. Experience in the use of various precision measurement instruments and standards.

SPECIALIZED EXPERIENCE: Must have experience or training with basic application of operating principles such as the production and utilization of oscillations over a broad range of frequencies; signal and waveform behavior, distortion, and amplification; pulse, trigger, and synchronization techniques; digital/analog processing and data conversion techniques; and a variety of display and indication methods. Experience in tracing signals and voltage paths, and skilled in the analysis of waveform characteristics such as timing, duration, frequency, and phasing. Originates test set-ups to isolate malfunctions and check performance characteristics of special or unique test panels or mockups. Experience in interpreting and applying a variety of technical electronic information such as schematic symbols, mathematical expressions and formulas, calibration procedures, and other reference materials. Experience in applying established techniques and methods of repair, testing, alignment, and calibration of equipment, which serves as test equipment or precision measurement standards. Experience in utilizing electronic circuits to measure electronic or electrical quantities to determine the performance characteristics and accuracy of other instruments and equipment.

It is not necessary for applicants to possess the MOS/AFSC listed as compatible to the position in order to apply, however applicant must meet the qualifications for the position. It is applicant's responsibility to acquire a compatible MOS/AFSC within 1 year of appointment. Coordinate with your unit's training representative to determine whether or not you can qualify for a specific MOS/AFSC and/or receive training within the 1 year timeframe before excepting the position.

How you will be evaluated

You will be evaluated for this job based on how well you meet the qualifications above.

Once the announcement has closed, your resume and supporting documentation will be used to determine if you meet the qualifications listed on this announcement. If you are minimally qualified, your resume and supporting documentation will be compared to your responses on the assessment questionnaire to determine your level of experience. If you rate yourself higher than is supported by your application package, your responses may be adjusted and/or you may be excluded from consideration for this position. If you are found to be among the top qualified candidates, you will be referred to the selecting official for employment consideration.

Your qualifications will be evaluated on the following competencies (knowledge, skills, abilities and other characteristics): Knowledge of Equipment Assembly; Trouble shooting; Use of Test Equipment.,

To apply for this position, you must submit a complete Application Package which includes:

Starting on September 27, 2025, federal agencies will only accept resumes up to two pages in length to comply with the Merit Hiring Plan. USAJOBS will not allow you to upload or build resumes longer than two pages, and you will need to update the resumes in your profile before applying to a job.


Two Page Resumes only.


1. A COMPLETE RESUME IS REQUIRED. Your full name, address, civilian email address (no .gov or .mil) and current telephone number must be on your resume. Your resume must clearly demonstrate experience that meets the requirements of this position. In describing your experience, please be clear and specific. We will not make assumptions regarding your experience. Your resume must show experience where you worked, job title, duties and accomplishments, employer's name and address, supervisor's name and phone number, starting and end dates (Mo/Yr), hours per week & salary. Incomplete resumes will result in the applicant not being considered for the position.

2. References must be submitted with the application packet. (Minimum of 3 references required). If no references are with the application packet, your application will not be sent forward to the selecting officials.

3. Prior/current Federal employees are required to submit their most recent SF 50 with their packet. The SF-50(s) must reflect the highest grade and step held in Federal Service that demonstrates one year time in grade.

4. A complete application package, including all supporting documents (i.e., resumes, copies of transcripts if required, licenses, All FAA Certifications and Credentials, and any other supporting documents etc.), must be submitted by 11:59 PM (EST) on the closing date of the announcement to receive consideration.

5. Copies of transcripts must be provided at the time of submission with the application packet. Failure to do so will result in the applicant not being considered for the position. Selected individual may be required to provide official transcripts prior to placement into this position.


PLEASE NOTE: It is the applicant's responsibility to verify that information entered and/or uploaded, (i.e., resumes, supporting documents, transcripts (copies) if needed, licenses, SF 50 etc.) is received, accurate, and submitted by the closing date. You may verify your documents have been processed with your application package successfully prior to the announcement closing. Uploaded documents may take up to one hour to clear the virus scan. Human Resources WILL NOT modify, change or add anything to your application packet after the closing date. Human Resources WILL NOT divulge if you are qualified or not for the position. Incomplete packets will not be considered for the position.

Next steps